en-us Wed, 22 Apr 2026 07:20:08 GMT 184782083 https://news.racingjunk.com/rear-ends/184782083/strange-hd-9-alu.-bare-center-with-tail-shaft-bearing.html I have a brand new strange alu. 9" heavy duty bare center case - also has the tail shaft bearing. it's part number N-2300. it has a 3.062" side bearings. here are the factory spec'sor heavy, high horsepower, or Street & Strip vehicle Differentials 28 & 31 spline POSI or 28, 31, & 33 splinespool This Case Uses A Special Strange Pinion Support(N-2322 AT EXTRA COST) It is made specifically for this case • Manufactured from 206-T4 heat treated aluminum •…

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Sat, 18 Apr 2026 20:57:16 GMT 184781634 https://news.racingjunk.com/rear-ends/184781634/tom-s-thirdmember-4.11-9.5-2-500.html Tom's Thirdmember 9.5" 4.11 Ratio in great condition/gear/parts like new. This has been a spare of ours and no longer needed.

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Tue, 14 Apr 2026 17:38:33 GMT 184780924 https://news.racingjunk.com/rear-ends/184780924/mark-williams-9.5-center-section-3.25.html Brand new Mark Williams 9.5” Extreme Third Member • 40 spline • 3.25 pro gear • 12-point hall effect sensor ring • 2nd gen U-bolt kit

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Sat, 11 Apr 2026 10:53:27 GMT 184704978 https://news.racingjunk.com/rear-ends/184704978/complete-rear-housing.html Strange Engineering Aluminum Rear Housing 33" Width Strange Engineering 9.5' Rear Center Section With 430 Ratio Pro Gears, Large Pinion And 1350 Yoke Strange Engineering 40 Spline Pro Axles, Rifle Drilled Strange Engineering Steel Disc Brakes Steel 4 Link Mounts With 1/2" Bolt Holes, 15 3/4" Center On Brackets 10 to 15 Runs On Rear Since New In 2022 Call Steve 410-360-4020

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Wed, 08 Apr 2026 07:45:10 GMT 184780506 https://news.racingjunk.com/rear-ends/184780506/ford-8.8-built-rear-end-3.73-spool-31-spline-bolt-in.html Ford 8.8 Mustang Stock Length Easy Bolt In 54" housing end to end, 59" wheel flange to flange, 5 lug conversion or drag car. Welded tubes, braced, 3.73, 31 spline spool and axles, c-clip eliminators, 94' V6 brakes, street beast control arms, stainless brake lines, strange 10 way struts, strut tower bar. $1,300 including shipping

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Tue, 07 Apr 2026 23:12:53 GMT 184779475 https://news.racingjunk.com/rear-ends/184779475/strange-9-locker.html Strange Engineering Cast Iron Case 4:10 35 spline Detroit Locker. New never installed cost $1,700 Asking $1,200

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Wed, 01 Apr 2026 18:58:49 GMT 184778720 https://news.racingjunk.com/rear-ends/184778720/strange-9-floater-rear-end.html Strange 9” Floater Rear End – Mark Williams center, 4.88 gears (rebuilt), 40-spline Strange axles & brakes. Ready to run.

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Mon, 30 Mar 2026 09:08:12 GMT 184778704 https://news.racingjunk.com/rear-ends/184778704/built-foxbody-8.8-rear-end-35-spline-spool-braced-dis.html For sale is an 8.8 rear end out of a fox mustang. It's narrowed, braced and has 9" Torino style ends on it. Specs below Housing width 45". Width with axles and brake rotors 50.5" Team z brace kit forward and lower. Tubes welded Moser 35 spline spool Moser 35 spline axles Motive 3.90 gear (new with no passes) Spherical bearings in upper ears Coil over brackets 1350 chromoly strange yoke Driveshaft speed sensor motion raceworks Trz upper control arms Trz lower control arm…

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Mon, 30 Mar 2026 02:39:44 GMT 184778700 https://news.racingjunk.com/rear-ends/184778700/strange-9-floater-rear-end-.html Strange 9” Floater Rear End – Mark Williams center, 4.88 gears (rebuilt), 40-spline Strange axles & brakes. Ready to run.

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Mon, 30 Mar 2026 00:35:00 GMT 184778321 https://news.racingjunk.com/rear-ends/184778321/strange-aluminum-center-section.html 35-spline big pinion centers 1: 4.57 Richmond | 2: 4.30 lightweight Ready to install – $1200 each / $2000 both

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Thu, 26 Mar 2026 14:39:37 GMT 184524089 https://news.racingjunk.com/rear-ends/184524089/quick-performance-ford-9-fabricated-chevy-s10-caltracs-new.html Fab 9 new stock length chevy s10 82-2003 1/4" wall tubbing internal gusset External back brace Jack pad, billet fill tube. Moser 40 spline gun drilled axles 5/8 studs and 1/2 dual drill patter Brand new in box Calvert caltracs Caltrac mono leafs Calvert leaf spring sliders Qa1 16 way shocks Calvert clatrac shocks as well. Willwood disc brake calipers aluminum brackets Center section can be purchased for additional $1400 new in box strange aluminum 3.250 9" lightweight spool 4.61 gears…

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Sun, 22 Mar 2026 07:45:10 GMT 182892364 https://news.racingjunk.com/rear-ends/182892364/12-bolt-moser-rear-end.html For sale a brand new (pristine condition) Mosier 12 bolt  rear-end differential with posit traction 33 spline axles.  Has Willwood 12 1/2 inch cross drilled rotors for piston calipers.  Has 1350 front yoke; stainless steel tubing for brake lines; set up for coil over shocks; an ultimate LPW rear cover and severical bearings in the upper mounts. It's powder coated gloss black. Has 373 gears and 7/16 wheel studs.  Have $5,000 invested and selling for $4400 This will fit an El Camino, Chevelle…

]]> Chassis/Suspension/Brakes/Driveline: Rear Ends Sun, 22 Mar 2026 07:45:10 GMT